|
|
Electronic Equipment & Components
|
Suppliers Directory
|
ACCUMET PRODUCTS
| | Address : |
348 ABDUL REHMAN ST JHAVERI HOUSE 4TH FLR |
| Telephone : |
22-3420340 |
| Send : |
On-Line Trade Inquiry |
| |
|
Products |
|
BORE MICROMETERS - THESE BORE MICROMETERS CORRESPOND TO APPROXIMATELY 1 TAPER PITCH OF CONE COMPARED TO 6 TO 40 FOR CONVENTIONAL CONE SYSTEMS.CAN PROVIDE VERY LARGE RANGE (UPTO 160 MM) IN A SINGLE BORE MICROMETER AT A VERY HIGH ACCURACY. STANDARD EXTENSIONS ARE AVAILABLE FOR MEASURING OF DEEP BORES UP TO 2500 MM. EACH EXTENSION IS PROVIDED WITH INDIVIDUAL MICROMETER HEAD OF THE INSTRUMENT, THEREBY SAVING TIME.
|
|
DIGITAL HARDNESS TESTERS - ELECTRONIC DIGITAL HARDNESS TESTER WORKS ON WELL ESTABLISHED ROCKWELL PRINCIPLE OF PRE LOAD AND TEST LOADS BOTH THE LOADS ARE APPLIED WITH ONE PRESSURE MOVEMENT OF PROBE THE DIGETAL HARDNESS TESTERS CAN MEASURE DIRECTLY ON VARIOUS HARDNESS SCALES SUCH AS HRC HRB HB/30 AND HV THESE ARE USED FOR ALL TYPES OF OBJECTS HARDNESS CAN BE TESTED EVEN WHEN THE METAL SHEETS ARE IN ROLLS SPECIAL FEATURES INCLUDE CARRYING OUT CORRECTION OF HARDNESS LIMITS STORING OF TEST VALUES IN MEMORY
|
|
3-POINT DIGITAL BORE MICROMETER - SYLVAC BS - SYLVAC BS II 3-POINT DIGITAL BORE MICROMETER IS AN IMPROVED VERSION BY ADDING ADDITIONAL FEATURES FOR ITS VERSATILITY AND EFFICIENCY WITH TWO PRESET MEMORIES, MODE OF TOLERANCE AND PRESET RECALL. THE VALUES MEASURED CAN BE READ ACCURATELY ON A LARGER DISPLAY WITH 0.001 MM/ 0.00005"RESOLUTION FOR THE DIAMETER RANGE 6-300 MM. A DIRECT RS-232C OUTPUT IS AVAILABLE TO CONNECT TO THE MICRO PRINTER OR A COMPUTER FOR PRINT OUT AND DATA PROCESSING. THE MEASURING ANVIL POSSESSES TUNGSTEN CARBIDE PINS IN ORDER TO HAVE HIGH WEAR RESISTANCE. THIS MICROMETER IS AVAILABLE FOR USE FOR ABSOLUTE OR COMPARATIVE MEASUREMENT FOR BATCH INSPECTION. THE 3-POINT MEASURING HEADS ENHANCE EASE AND ERROR-FREE OPERATION AND CAN BE DISTRIBUTED IN SETS OR AS AN INDIVIDUAL INSTRUMENT AS PER THE STIPULATED RANGE. THE 1-6 MM RANGE CAN BE AVAILABLE WITH 2-POINT ANVILS. SPECIAL MEASURING HEADS COULD BE AVAILABLE FOR APPLICATIONS - SCREW THREADS, GROOVES, SPHERICALS, ETC. DEEP BORES UP TO 8 METRES CAN BE PROVIDED WITH AN EXTENSION.
|
|
HARDNESS TESTER, PORTABLE ELECTRON - ACCUMET PRODUCTS OFFERS COMPUTEST, A PORTABLE ELECTRONIC DIGITAL HARDNESS TESTER, WHICH WORKS ON THE WELL ESTABLISHED ROCKWELL PRINCIPLE OF PRE LOAD AND TEST LOAD. BOTH THESE LOADS ARE APPLIED WITH ONE PRESSURE MOVEMENT OF PROBE (ZERO SETTING IS CARRIED OUT ELECTRONICALLY). THE MEASURED HARDNESS TEST VALUE APPEARS ON THE DISPLAY ON RELEASING OF PRESSURE. COMPUTEST CAN MEASURE DIRECTLY ON VARIOUS HARDNESS SCALES SUCH AS HRC, HRB, HB/30, AND HV. SPECIAL HARDNESS SCALES CAN BE PROVIDED ON REQUEST. IT CAN ALSO INDICATE THE MINIMUM THICKNESS REQUIRED FOR SPECIMENS OF DIFFERENT HARDNESS. IT CAN MEASURE HARDNESS OF ALMOST ALL KINDS OF METALS WITHOUT CHANGING THE INDENTOR, AND CAN BE USED FOR ALL TYPES OF OBJECTS WHETHER SMALL, BIG, LIGHT OR HEAVY. EVEN THIN PLATES AND SHEETS (IN ROLLS) CAN ALSO BE TESTED. ADAPTORS ARE PROVIDED FOR TESTING ON CURVED SURFACES. SPECIAL FEATURES INCLUDE CARRYING OUT CORRECTION OF HARDNESS CURVES, SETTING OF MIN AND MAX TOLERANCE LIMITS, STORING OF TEST VALUES IN MEMORY, DISPLAYING OF AVERAGE AND STANDARD DEVIATION, ETC. IT CAN BE DIRECTLY CONNECTED TO STANDARD DOT MATRIX PRINTER AND IT PRINTS DETAILED RESULT.
|
|
PORTABLE HARDNESS TESTER - TH 1 - ACCUMET PRODUCTS OFFERS A LOW COST COMPACT AND LIGHTWEIGHT (180 GM) PORTABLE DYNAMIC HARDNESS TESTER WITH A BUILT-IN PROBE, MODEL TH 130, IDEALLY SUITABLE FOR IN SITU TESTING OF MEDIUM AND LARGE SIZE COMPONENTS SUCH AS STEEL ROLLS, MOULDS, DIES, MACHINE TOOL BEDS, CRANKSHAFTS, CYLINDER BLOCKS, CASTINGS, FORGINGS, ETC. IT IS ALSO HANDY FOR TESTING HARDNESS OF MASS/BATCH PRODUCED COMPONENTS ON PRODUCTION LINES. AND CAN BE EASILY CARRIED TO FIELD OR SHOP FLOOR FOR ON THE SPOT TESTING. IT IS VERY USEFUL FOR TESTING OF INCOMING MATERIALS IN THE STORES. TH 130 WORKS ON LEEBS PRINCIPAL AND CONVERTS THE HARDNESS VALUES AUTOMATICALLY TO THE COMMONLY USED HARDNESS SCALES SUCH AS ROCKWELL, VICKERS, BRINELL SHORE, ETC. THE DISPLAY AUTOMATICALLY SHOWS AVERAGE VALUE OF EACH GROUP READINGS (UP TO 9) AND THESE CAN BE STORED IN MEMORY FOR PRINTING OR DOWN LOADING TO PC AT A LATER STAGE. TH 130 CAN BE USED AT ANY ANGLE AND IT WORKS ON A RE-CHARGEABLE BATTERY AND HAS SPECIAL SUPPORT RINGS ARE AVAILABLE TO TEST ON CURVED AND PROTRUDED SURFACES. STANDARD TEST BLOCK IS SUPPLIED FOR VERIFYING THE ACCURACY OF THE TESTER PERIODICALLY.
|
|
DIGITAL FORCE (PUSH-PULL) GAUGES - SERIES F - DIGITAL FORCE GAUGES SERIES FGN AND FGC PROVIDE ECONOMICAL SOLUTION FOR FORCE MEASURING APPLICATIONS. THESE HAND HELD FORCE GAUGES ARE VERY COMPACT AND LIGHT WEIGHT AND HAVE RUGGED ALUMINUM DIE CAST BODY TO WITHSTAND ROUGH CONDITIONS. THE FUNCTIONS INCLUDE NORMAL/PEAK MEASUREMENTS AND FLOATING ZERO. THE LARGE DISPLAY CAN BE REVERSED FOR TENSILE FORCE MEASUREMENTS. IT ALSO DISPLAYS LOW BATTERY, BATTERY BEING CHARGED, OVER LOADED AND PEAK HOLD MODE WARNINGS/CAUTIONS. THE MEASURING UNITS CAN BE SELECTED FROM DIFFERENT SYSTEMS TO READ IN KG/M, LB/FT OR NM AND RANGES FROM ±0.2 KGF TO ±50 KGF AND RESOLUTION FROM 0.1 G TO 10 G AS PER THE MODEL. IT OPERATES ON RECHARGEABLE NICD BATTERY OR ON AC MAINS THROUGH AN ADAPTOR. SERIES FGC HAS RS-232 AND ANALOGUE OUTPUTSTHE GAUGES CAN BE USED TO MEASURE VARIOUS FORCES SUCH AS TENSION, COMPRESSION, BRAKE, PEELING, SEALING, UNSEALING, ETC. USER AREAS INCLUDE CHECKING OF DOOR LOCKS, HOOD, GLOVE COMPARTMENT, BRAKE PEDAL, PRESSURE OF WIPER BLADE ON WINDSHIELD IN AUTOMOBILES. IN ELECTRONICS FIELD, CHECKING THE TIGHTNESS OF CONNECTORS, SOLDERING FORCE, CRIMPED TERMINALS AND CABLES IS POSSIBLE. OTHER APPLICATIONS ARE CHECKING CRUSH STRENGTH OF TABLETS, TENSILE STRENGTH OF RUBBER, TRIGGER FORCE OF POWER TOOLS AND FIRE ARMS, TESTING OF SPRINGS, PEELING FORCE OF ADHESIVE TAPES AND LABELS.
|
|
LONG RANGE COATING THICKNESS GAUGES - QUANIX 1200/15 - QUANIX SERIES OF COATING THICKNESS GAUGES FROM AUTOMATION, GERMANY, AN ISO-9000 COMPANY, HAVE MANY SUPERIOR FEATURES. THESE GAUGES DO NOT REQUIRE ANY CALIBRATIONAND COME WITH BUILT-IN PROBES WITH NON-WEARING RUBY TIP TO ENSURE EXTRA LONG LIFE AND PRECISION EVEN UNDER ROUGH CONDITIONS. V-GROOVE IS PROVIDED IN THE PROBE FOR CYLINDRICAL COMPONENTS AND DOES NOT HAVE PLUGS, CABLES AND SOCKETS THAT CAUSE POSSIBLE SERVICE PROBLEMS. THIS GAUGE WEIGHS ONLY 130 G INCLUDING BATTERY. QUANIX 1500 HAS EXTRA LONG RANGE OF 5,000 MM (5 MM) AND DUAL PROBES AND READOUTS FOR FERROUS AND NON-FERROUS MATERIALS, WHICH MAKES IT A 4 IN 1 INSTRUMENT AT A MUCH LOWER COST. QUANIX 1200 IS WITH A SINGLE BUILT-IN PROBE FOR FERROUS BASE MATERIALS AND HAS A RANGE OF 0-2,000 MM (2 MM). BOTH QUANIX 1500 AND 1200 HAVE RESOLUTION RANGING FROM 0.1MM (0.0001 MM) TO 0.01 MM AS PER THE MEASURING RANGE.
|
|
HIGH PRECISION COMPACTOR - MICROCATORS ARE PRECISION COMPARATORS HAVING SPECIAL TORSION-TYPE MECHANISM DIFFERENT FROM THE MECHANISM OF CONVENTIONAL PLUNGER-TYPE DIAL GAUGES, WHICH ENSURE LOW FRICTION MOVEMENT OF THE SPINDLE, WHICH RESULTS IN VERY HIGH SENSITIVITY, ACCURACY AND LONG LIFE. THESE FEATURES MAKE MICROCATORS HIGHLY RELIABLE MECHANICAL COMPARATORS FOR THE INSPECTION OF PRECISION PARTS AND ARE AVAILABLE WITH SHANK DIAMETERS OF 8 MM AND 28 MM. RESOLUTIONS AVAILABLE ARE 0.001 MM AND 0.0005 MM (ONLY FOR 28 MM DIA SHANK). MICROCATORS WITH 28-MM DIA SHANK ARE FOR HEAVY DUTY AND HAVE AGATE CONTACT TIP FOR HIGH WEAR RESISTANCE. THE MEASURING RANGES ARE 0.03 MM AND 0.015 MM AS PER THE RESOLUTION AND CAN BE MOUNTED ON STANDARD COMPARATOR STANDS WITH CLAMPING DIAMETER OF 8 MM OR 28 MM AS PER THE SHANK DIAMETER.
|
|
INTERNAL GROOVE DIAL CALLIPERS - INTERNAL GROOVE DIAL CALLIPERS ARE EXTREMELY USEFUL FOR CHECKING OF INTERNAL GROOVE DIAMETERS, RECESSED BORES AND PLAIN BORES. AVAILABLE IN THE RANGE FROM 3 MM TO 200 MM AND RESOLUTION OF 0.025 MM OR 0.01 MM AS PER THE MODEL, THE DIAL HAS ROTATABLE BEZEL FOR SETTING ZERO AND A PROVISION FOR LOCKING. IT HAS PLASTIC GLASS TO AVOID BREAKAGE. MEASURING ARMS CAN BE MOVED IN A SIMPLE OPERATION WITH A PUSHBUTTON OR WITH A LEVER. DIAL CALLIPERS CAN BE EASILY SET WITH A MICROMETER OR A RING GAUGE. REVOLUTION COUNTER IS PROVIDED FOR EASY INTERPRETATION. CONTACT POINTS ARE EITHER FIXED OR INTERCHANGEABLE AS PER THE MODEL. SOME OF THE MODELS ARE PROVIDED WITH JEWELLED MOVEMENT.
|
|
CALIPERS FOR 3 & 5 FLUTED CUTTER - VERNIER CALIPERS WITH VEE JAWS HAS THREE CONTACT FACES TO MEASURE THE DIAMETERS OF REAMERS, MILLING CUTTERS, END MILLS, TAPS, GEARS, SPLINE SHAFTS AND THE LIKE HAVING 3 TO 5 FLUTES/FACES OR UNEVEN NUMBERS OF FLUTES/FACES WHICH CAN BE DIVIDED BY 3 OR 5 AND ARE EVENLY SPACED. THESE CALIPERS ARE IDEAL, FOR CHECKING OUT OF ROUNDNESS (LOBING EFFECT) OF THE COMPONENTS AFTER CENTRELESS GRINDING OPERATION. THE DIAMETERS CAN BE DIRECTLY READ ON THE CALIPERS WITH A RESOLUTION OF 0.05 MM. THE MEASURING RANGE IS 4-40 MM, FOR WHICH NORMALLY 2 OR 3 VEE ANVIL MICROMETERS ARE REQUIRED FOR EACH TYPE (3 AND 5 FLUTES). THEREFORE, VEE ANVIL CALIPERS WORK OUT ECONOMICAL.
|
|
PORTABLE METALLOGRAPHIC TEST EQUIPMENT - XH-5 - PORTABLE METALIDGRAPH XH-500 EQUIPMENT IS DESIGNED TO CARRY OUT NON-DESTRUCTIVE SAMPLE PREPARATION AND MICROSCOPIC TEXTURE INSPECTION ON SITE. IT CAN BE USED FOR METALLOGRAPHIC EXAMINATION OF PIPES, PLATES, FORGINGS, CASTINGS, AND METAL STRUCTURES MADE FROM VARIOUS METALS AND ALLOYS, IGCC TEST AS PER ASTM A262 PRACTICE A, FAILURE ANALYSIS BY SEM USING REPLICA METHOD, LIFE ASSESSMENT OF EQUIPMENTS, STRUCTURES AND COMPONENTS WORKING UNDER HIGH PRESSURE AND TEMPERATURE, CHECKING OF MICROCRACKS IN WELD JOINTS, DEFECTS IN PRESSURE VESSELS AND PIPELINES, AND PREPARATION FOR X-RAY ANALYSIS WITHOUT CAUSING PROCESSING STRAINS. ITS USEFUL IN INDUSTRIES SUCH AS PETROCHEMICAL; CHEMICAL, REFINERIES, FORGING, FOUNDRIES, ROLLING MILLS, HEAT TREATMENT SHOPS, POWER PLANTS, AND FOR INSPECTION AGENCIES. THE XH-500 COMPRISES A MINI GRINDER, ELECTROLYTIC POLISHING UNIT, AND PORTABLE MICROSCOPE UP TO 500X MAGNIFICATION MAGNETIC BASE, POWER SUPPLY, CONSUMABLES AND A CARRYING CASE.
|
|
DIGITAL LEVEL & INCLINOMETER - PRO 360/36 - PRO-3600 AND PRO-360 ARE NEW GENERATION DIGITAL LEVEL AND ANGLE MEASURING INSTRUMENTS WITH MULTI-FUNCTIONS. THE MEASURING RANGE IS 360° (4 X 90°) AND RESOLUTION RANGES FROM 0.01° TO 0.2° DEPENDING UPON THE RANGE USED. THE INSTANT LCD DISPLAYS LEVEL, TILT, TRUE VERTICAL OR ANY ANGLE IN BETWEEN. FLOATING ZERO PROVIDES ZERO SELECTION ANYWHERE WITHIN ITS 360° RANGE AND COMES WITH OTHER FUNCTIONS SUCH AS HOLD TO FREEZE DISPLAY, RESET PLUS SUPERSET SELF CALIBRATION MODES, AUTO OFF, AND LOW BATTERY INDICATOR. THE BODY IS MADE OF HIGH IMPACT MACHINED ALUMINIUM FRAME WITH A V-GROOVE IN THE BASE FOR CURVED/CYLINDRICAL SURFACES. THESE LEVELS OPERATE ON 9-V ALKALINE BATTERY WITH MANY HOURS OF LIFE. THESE DIGITAL LEVELS ARE USEFUL FOR SETTING THE EQUIPMENTS, MEASUREMENTS OF ANGLES, SLOPES, STRAIGHTNESS, FLATNESS, SQUARENESS AND PARALLELISM QUICKLY AND ACCURATELY. USER AREAS INCLUDE: MACHINE TOOLS, AUTOMOBILES, SHIPYARDS, MACHINERY PRODUCTION, BRIDGE BUILDING, NUCLEAR PLANTS, AND MAINTENANCE SHOPS.
|
|
DYNAMIC HARDNESS TESTER - TH-1 - TH-130 IS AN ULTRA-COMPACT POCKET SIZE DIGITAL DYNAMIC HARDNESS TESTER WEIGHING ONLY 190. IT WORKS ON A RECHARGEABLE BATTERY AND DOES NOT HAVE ANY PLUG, SOCKET OR CABLE, AND HENCE IS FULLY SELF-CONTAINED AND IS IDEAL FOR: CHECKING HARDNESS OF MEDIUM AND LARGE SIZE COMPONENTS, MOULDS, DIES, MACHINE TOOL BEDS, BEARINGS AND SIMILAR PARTS ON PRODUCTION LINE; FAILURE ANALYSIS OF PRESSURE VESSELS, TURBO-GENERATORS, TESTING AT VENDOR'S PLACE; AND, MATERIAL IDENTIFICATION IN STORES AND MANY MORE OTHER USES. IT CAN BE USED FOR HARDNESS TESTING OF MANY TYPES OF METALS SUCH AS STEEL, ALLOY TOOL STEEL, STAINLESS STEEL, GREY CAST IRON, SPHEROIDAL IRON, ALUMINIUM, BRASS, BRONZE, COPPER, ETC. IT CAN INDICATE HARDNESS IN HL (LEEB'S), HB, HRC, HRB, HRA, HV AND HS SCALES. ACCURACY IS ±1%.
|
| |
|
View More Supplier Pages
Page(s) : 1 •
2 •
3 •
4 •
5 •
| |
|
|
|
